Guidelines and Limitations for Firepower Interface Configuration

When you use CDO to configure the device, there are several limitations to interface configuration. If you need any of the following features, you must use Firepower Management Center to configure the device.

Firewall

  • Routed firewall mode only is supported. You cannot configure transparent firewall mode interfaces.

  • Only physical firepower 1010 devices support interfaces configured for switch port mode. See Switch Port Mode Interfaces for an FDM-Managed Device for more information.

Passive

  • At this time, CDO does not identify passive interface mode in the interface table ad you cannot configure passive or ERSPAN interfaces. You must use the FDM-managed UI to configure and identify passive interfaces.

IPS-Only Mode

  • You cannot configure interfaces to be inline (in an inline set), or inline tap, for IPS-only processing. IPS-only mode interfaces bypass many firewall checks and only support IPS security policy. In comparison, Firewall mode interfaces subject traffic to firewall functions such as maintaining flows, tracking flow states at both IP and TCP layers, IP defragmentation, and TCP normalization.

  • Optionally, you can configure IPS functions for this firewall mode traffic according to your security policy.

EtherChannel

CDO supports read, create, and abilities for devices running Version 6.5 and later. To create Etherchannel interfaces, see Add an EtherChannel Interface for an FDM-Managed Device for more information. To create

  • You can configure up to 48 EtherChannels on physical Firepower devices, although how many interfaces can be active at a time depends on your device model. For device-specific limitations, see Device-Specific Requirements.

  • All interfaces in the channel group must be the same media type and capacity, and must be set to the same speed and duplex. The media type can be either RJ-45 or SFP; SFPs of different types (copper and fiber) can be mixed. You cannot mix interface capacities (for example 1GB and 10GB interfaces) by setting the speed to be lower on the larger-capacity interface.

  • The device to which you connect the EtherChannel must also support 802.3ad EtherChannels.

  • The FDM-managed device does not support LACPDUs that are VLAN-tagged. If you enable native VLAN tagging on the neighboring switch using the Cisco IOS vlan dot1Q tag native command, then the FDM-managed device will drop the tagged LACPDUs. Be sure to disable native VLAN tagging on the neighboring switch.

  • All FDM-managed device configuration refers to the logical EtherChannel interface instead of the member physical interfaces.

    Note

    Interfaces set up as portchannels can only use physical interfaces, redundant interfaces, and subinterfaces are supported as bridge group member interfaces.

Bridge Groups

At this time, CDO supports the configuration of one bridge group. To determine if your device supports bridge groups, see Bridge Group Compatibility in FDM-Managed Device Configurations for more information.

When adding an interface to a bridge group, keep the following in mind:

  • The interface must have a name.

  • The interface cannot have any IPv4 or IPv6 addresses defined for it, either static or served through DHCP.

  • BVI can have either VLAN interfaces or other routed interfaces as a member interface, but you cannot have both as member interfaces on a single BVI.

  • BVI can have either VLAN interfaces or other routed interfaces as a member interface, but you cannot have both as member interfaces on a single BVI.

  • The interface cannot be Point-to-Point Protocol over Ethernet (PPPoE)

  • The interface cannot be associated with a security zone (if it is in a zone). You must delete any NAT rules for the interface before you can add it to a bridge group.

  • Enable and disable the member interfaces individually. Thus, you can disable any unused interfaces without needing to remove them from the bridge group. The bridge group itself is always enabled.

  • You can configure the interfaces that will be members of the bridge group. See Configure a Bridge Group for interface requirements and creation.

Point-to-Point Protocol over Ethernet

  • You cannot configure Point-to-Point Protocol over Ethernet (PPPoE) for IPv4. If the Internet interface is connected to a DSL, cable modem, or other connection to your ISP, and your ISP uses PPPoE to provide your IP address, you must use the FDM to configure these settings.

VLAN

To configure VLAN interfaces and VLAN members, see Configure an FDM-Managed Device VLAN for more information. To configure VLAN for switch port mode, see Configure an FDM-Managed Device VLAN for Switch Port Mode for more information.

  • The interface must be physical.

  • The interface cannot be management-only.

  • The interface cannot be associated as any other type of interface, including BVI, subinterfaces, another VLAN interface, EtherChannel, etc.

  • The interface cannot be a BVI member or an etherchannel member.

  • Device models support varying numbers of VLAN members. See Maximum Number of VLAN Members by Device Model for more information.

    Note

    To configure VLAN for your environment, see Configure Firepower VLAN Subinterfaces and 802.1Q Trunking for more information.

Network Module Cards

Optional network module installations are limited to the ASA 5515-X, 5525-X, 5545-X, and 5555-X, and the Firepower 2100 series devices.

  • Cards are only discovered during bootstrap (that is, initial installation or reimage, or when switching between local/remove management). CDO sets the correct defaults for speed and duplex for these interfaces. If you replace an optional card with one that changes the speed/duplex options for the interfaces, without changing the total number of interfaces available, reboot the device so that the system recognizes the correct speed/duplex values for the replaced interfaces. From an SSH or Console session with the device, enter the reboot command. Then, using CDO, edit each physical interface that had capability changes and select valid speed and duplex options, as the system does not automatically correct your original settings. Deploy your changes right away to ensure correct system behavior.

  • You cannot enable or disable network modules or perform breakout online insertion and removal (OIR) of interfaces on FDM-managed Secure Firewall 3100 series devices.

  • Note

    Replacing a card with one that changes the total number of interfaces, or removing interfaces that were referred to by other objects, can result in unexpected problems. If you need to make this kind of change, please first remove all references to the interfaces you will remove, such as security zone membership, VPN connections, and so forth. We also suggest you do a backup prior to making the change.

Interfaces on Virtual FDM-Managed Devices

  • You cannot add or remove interfaces without reinitializing a virtual FDM-managed device. You must execute these actions in an FDM-managed device.

    Note

    If you replace interfaces with ones that have different speed/duplex capabilities, reboot the device so that the system recognizes the new speed/duplex values with the following procedure: from the device's CLI console, enter the reboot command. Then, in CDO, edit each interface that had capability changes and select valid speed and duplex options, as the system does not automatically correct your original settings. Deploy your changes right away to ensure correct system behavior.